Heating Services

Furnaces are rated by the Annual Fuel Utilization Efficiency (AFUE) ratio, which is the percent of heat produced for every dollar of fuel consumed,or how efficiently a furnace converts gas into heating energy. Its AFUE rating is measured as a percentage.

Like the miles-per-gallon rating on your automobile, the higher the AFUE rating, the lower your fuel costs. An AFUE of 90% means that 90% of the energy in the fuel becomes heat for the home and the other 10% escapes up the chimney and elsewhere. According to the EPA- AFUE doesn’t include the heat losses of the duct system or piping, which can be as much as 35% of the energy for output of the furnace when ducts are located in the attic, garage, or other partially conditioned or unconditioned space. All furnaces manufactured today must meet at least 80% AFUE in the south and 90% AFUE in the North. If your furnace is 10 – 15 years old, it very well may fall below the current furnace minimum and waste energy- costing you money.

When shopping for high-efficiency furnaces and boilers, look for the ENERGY STAR® label. If you live in a cold climate, it usually makes sense to invest in the highest-efficiency system. In milder climates with lower annual heating costs, the extra investment required to go from 80% to 90% to 95% efficiency may be hard to justify.

This doesn’t mean that you should only select a furnace based on its AFUE rating. The efficiency rating is just one factor to consider when looking for a new furnace.

Two-stage heating means the furnace has two levels of heat output: high for cold winter days and low for milder days. Since the low setting is adequate to meet household heating demands 80% of the time, a two-stage unit runs for longer periods and provides more even heat distribution.

There are a few obvious signals that let you know when it’s time to upgrade your heating system. Frequent repairs, recent spikes in utility bills, and inconsistent temperatures in the home are a few warning signs that it’s time for a new heater. But if you’ve had the same heating system for twenty years or more, it would be a good idea to talk to an HVAC contractor about having it inspected to determine if it’s time for a heater replacement. Even if your old heater has worked without problems for years, a professional heating technician is trained to detect any possible operation or safety issues that are a direct indication that the system needs to be replaced. If you are concerned about your heating costs, you should talk to a heating professional about other options. Call us now to schedule your system’s check up!

You may not find the filter in your home or business to be very important, but you should! There are actually 3 ways air can get filtered-1) through your AC filter, 2) it will get filtered through the AC coil and 3) it will get filtered again through YOURS and YOUR FAMILY’S lungs! Furnace manufacturers put inexpensive fiberglass filters into their furnaces to remove airborne particles that might damage the fan and the heating coil. Particle buildup can also decrease the efficiency of your furnace, as the furnace has to work harder to pull air through the return. More expensive filters can also improve the air quality in your house by removing pollen, bacteria and mold spores from the air. Don’t let YOUR lungs be the filter for your air conditioner! Use the maximum efficiency filter designed for your system. This is especially important if you or someone in your family suffers from allergies or respiratory illnesses. If you do not know which filter that may be, then just ask us, we will be glad to point you in the right direction!

Check the documentation that came with your furnace. Recommendations vary based on a number of factors: the type of filter that you use, how many pets you have, whether anyone in your home has allergies, etc. If you use disposable fiberglass panel or electrostatic panel filters, you should change them anywhere from once a month to once every three months. Pleated filters generally last from 3 months to 6 months, again, always check your filter monthly, no matter what type filter you use. Filters are relatively inexpensive and easy to change, so there is little reason to wait. If you don’t change or clean your filter often enough the filter can get clogged with dust and other airborne particles, forcing your furnace to work harder to maintain airflow. This will reduce your furnace’s efficiency and can cause damage.

Furnace technology has advanced significantly in recent years. Modern furnaces are designed to provide more even and efficient heating than past furnaces, which can impact both how your system operates,sounds and what you notice about your system.

To better regulate temperatures and airflow, modern furnaces move more air over the heat exchanger than older furnaces. The air that comes out of your furnace registers may not seem as warm as the air from your old furnace, but overall airflow is improved. Better airflow means higher comfort.

Also, new furnaces are designed to integrate with high-efficiency air conditioners, so furnace blowers are more powerful to accommodate add-on cooling. Since cold air is much heavier than warm air, your system needs an extra boost from the blower to deliver cool air throughout your home. If you have an older home, this performance boost could produce unfamiliar sounds because air duct systems were originally designed for heating only. To minimize sound levels, choose a variable speed product which automatically changes speeds to meet the airflow needs of both heating and cooling cycles.

It’s recommended that you schedule a maintenance service visit once a year with a licensed HVAC technician. This will prolong the life of your heating system and keep it running safely and efficiently throughout the cold season. A qualified heating technician will thoroughly clean and inspect all of your heater’s components and make any necessary repairs or adjustments. Not only does this ensure that your heater is performing at optimal levels, which helps to save on overall heating costs, but it also allows the technician to address any major problems or safety concerns.

It is a temperature-sensitive device that controls and regulates the temperature in a space for systems such as a furnace, air conditioner, or both. When the indoor temperature drops below or rises above the thermostat setting, the device initiates or terminates either the heat or cooling modes, depending upon the thermostat setting and temperature set point. When initiated your furnace or air conditioner runs to warm or cool the house air to the setting you selected for your family’s comfort.

There are five basic types of automatic and programmable thermostats:

Manual
Digital
Digital- Non- Programmable
Digital- Programmable
Remote Access
Touchscreen
Wireless-WiFi
Smart

Most range in price, call and ask us which is best for you. Think thermostats don’t matter? Think Again! Thermostats control half of your home’s energy use. That is more than appliances, computers, stereos and lighting combined